Irrigation Supplies Burbank

Once you have completed the preparation stage which include measuring just how much artificial grass you will need, installing appropriate drainage (if required) and removing the natural grass layer, you will be able to install your artificial grass lawn. This short article outlines the steps you ought to follow to help you to get the job done right, from laying the base, connecting joints and preventing weed growth.

Lay Gravel Base followed by Sharp Sand – If required, use treated timber/timber stakes to place inside an area frame. We recommend 4 X 2 inches of tantalised treated timber for heavy clay soil areas and poorly draining areas and two X 2 inches of tantalised timber permanently draining areas. Screw these timbers for the stakes leaving the stakes on the inside of the perimeter. In case the Artificial Grass meet a concrete path, wall or decking, position the timber flush with the surface height and also by using 10mm temporary fillet, pack the timber near the wall leaving the area to help you tuck the Artificial Grass between the timber and the adjoining material in a later stage.

Position the stakes up against the inner perimeter timber edging and hammer in to the ground ensuring the stakes are slightly less than the timber edging. Next screw the timber stake for the timber edging. With heavy clay soils we recommend laying a crushed stone surface of up to 3 inches. This will not be necessary for the majority of areas and merely required for those who have a high water table where the ground holds water for long periods of your time after it rains. Next compact the floor utilizing a vibrating plate which can be hired from an equipment hire company. Ensure the perimeter is compacted and beneath the timber edging by 1 inch. Infill the perimeter with sharp sand and level using a rake. Guarantee the sand is level to the peak from the timber edging and compact again.

For good drainage areas spread a layer of sharp sand to blind on the soil. Next compact the ground using a vibrating plate that may be hired from an equipment hire company. Guarantee the perimeter is compacted and level with the timber edging. If you put more work in at this time, your Artificial Grass Lawn will look better because of this.

Weed Control Layer – Apply the weed control geo textile membrane and cut as necessary. Tack using small 1 inch galvanised clout nails towards the timber edging. This weed control geo textile membrane prevents any chance of weed growth through the artificial grass drainage holes.

Roll out Artificial Grass – Lay the Artificial Grass inside the desired direction working on the carpet and not on the levelled base. Make sure the carpet is positioned to minimise cuts, joints and waste overlaying the timber edging by at least 4 inches. When the artificial grass meets a path or edge, and if you have laid the timber edging correctly as previously described, then the artificial grass may be wedged between. If joining, please be sure that the artificial grass is laid with all the pile running in the same direction on each piece. Lay the carpet along with the sand instead of dragging it over the base material. To help stop wrinkles or creasing you should allow 2 to 3 hours to settle before continuing with jointing and adhesive. Cut grass to shape utilizing a sharp Dolphin or Stanley knife or scissors.

Jointing – When jointing your outdoor carpet together, make sure the pile runs in the same direction. Shut down manufacturer’s edge strip (if present) and butt two edges together ensuring you can find no gaps greater than 1mm between the two carpet edges. The accuracy of the will determine how visible the join is right after the completion. Fold back edges and position jointing tape (smooth side down) in order that the edges of the carpet satisfy the tape when joined.

Adhesive – a) Apply the cartridge adhesive in a zig zag motion on the rougher side in the tape allowing one cartridge for each 3 linear metres. Turn down carpet and press both edges into the wet adhesive, ensuring every piece marries up and it has no overlap. As you are accomplishing this together with your fingers, mix the fibres together to conceal the join. When the whole length is in place and also you are happy using its appearance it really is essential to walk over the join several times to activate the glue and bond the grass for the tape. Weigh on the seam to ensure good exposure to the glue until it cures. The more care taken using the operation the neater and tidier the joint is going to be.

b) If using the 2-component multi-purpose adhesive, ensure thorough mixing of the two components before use. Apply adhesive to the rough side from the tape and spread evenly across a width of at the very least 20cm using if possible a notched trowel. Sufficient adhesive ought to be applied to ensure that once the artificial grass carpet is pressed in to the adhesive, a transfer over the carpet backing is complete. Reject carpet and press both edges in to the wet adhesive, ensuring each piece marries up and has no overlap. Ensure the carpet will not crest at the seam and is holding flat within the bonded area. After the whole length is at place and you are pleased using its appearance it really is essential to walk over the join repeatedly to activate the glue and bond the grass for the tape. Weight the seam to make certain good contact with the glue until it cures. The more care taken using the operation the neater and tidier the joint will be.

While you should endeavour never to put adhesive to the carpet small quantities of glue can be taken off from your artificial grass fibre using White Spirit as well as a small off cut in the artificial grass. Small amounts of cured glue can usually be removed. To avert this situation and the chance of injury to the artificial grass, care and precautions should be delivered to avoid vhhfqr with all the fibres constantly. If the artificial grass has become jointed and glued and you also are happy using the levels screw the grass for the timber perimeter framework using galvanised screws at a minimum of 12 inch intervals.

Spread Sand (Optional, depending on Grass Selected) – Once the artificial grass has become laid use silica sand, that is kiln dried and brush into carpet along the way. Each product might have sand infill but this can be only employed to stabilise the carpet and at no time if the sand be visible. You need to get an even spread on the surface utilizing a brush to build up the depth in layers. Usually do not apply the sand in a single application. Brush sand into pile soon after laying as the artificial grass is dry and even though weather conditions are good. Brush vigorously against the fibres from the carpet pile to encourage the tufts to stand upright. Putting the proper quantity of sand in helps retain the artificial grass to sleep down, protects the fibres and in addition keeps them standing allow it the look of real grass.

Artificial Turf Installation Burbank – Read Through This Post..

We are using cookies on our website

Please confirm, if you accept our tracking cookies. You can also decline the tracking, so you can continue to visit our website without any data sent to third party services.