This automated optical fiber tensile testing program is made for operator skill impartial use in production and lab settings. Two fundamental model configurations allow the consumer to pick between a set up for standard linear evidence testing with extra mandrels for rotary high strength testing.

The linear version is ideal for creation evidence screening with causes approximately 22 N. Motor-driven clamps with very carefully developed rubber inserts ensure that the Optical Fiber Ribbon Machine will not be ruined inside the testing process while concurrently getting rid of the requirement for an outside air provide. Amounts of tugging force, tugging velocity and hold time are programmable and conveniently offered to the operator with the built in LCD touch-screen control. Information from tests can be saved and accessed via the USB dock or Ethernet user interface.

Mandrels of the same style like NYFORS’ optical fiber recoaters can easily be installed on the evidence tester inside the rotary higher power configuration. The fiber is covered round the two mandrels which assistance it using a unique clamping mechanism. By doing this much higher lots can be used to the fiber, enabling breaking up strength tests below managed conditions.

Adjustable clamp placement facilitates testing with the highest force levels as well as testing of short fiber lengths. The lightweight and light weight design helps make the tool simple to move around in a lab environment and also to integrate in a creation work bench in which space is at reasonably limited. The device is a lightweight and light-weight tool perfect for screening the strength of optical materials approximately 30 N. The equipment is created to meet all types of programs where a strength check needs to be performed.

The machine is made with the consumer in mind. The FTTH Cable Production Line is easily put into the guided linear clamps, as well as the testing starts instantly using a “One Touch” go button. The built in microprocessor controls all the important parameters like pulling force, tugging speed and hold time. This permits for a totally managed test every time.

The machine can be attached to another Computer, which enables use of all programmable guidelines and settings. The device is adapted to stand-on your own use or to the integration into different subsystems. The equipment posseses an substantial capability of signing and saving details including tugging force, pulling velocity and fiber diameter along with other guidelines.

Two recoat injector configurations are available. The PTR307 utilizes a computerized water pump to inject the recoat materials. The quantity of materials dispensed through the automated injector is managed by hand using the top-installed “Inject” button or programmed into the machine making use of the tablet controller. The PTR307B includes a manual recoat injection program that will require the consumer to personally dispense the recoat materials to the mold cavity; another one injector for that PTR307B recoater is available below. Please note that this automated injector is just compatible with higher-index recoat materials, while the manual injector works with each low- and high- directory recoat material; both are sold separately below. Please contact Tech Assistance to learn more.

he manual injector can be installed to compatible SZ Stranding Line using the 4-40 anchoring screws on the recoater housing (see photo to the right). Use a 3/32″ hex key to safe the injector before use. To get in touch the PTRRRM for the recoater mold, tighten the connector at the end of the eco-friendly plastic material tubes, then release by a 1/4 consider permit rotation.

The injector is equipped with a syndication valve and 2-place choice handle for directing the stream of recoat material. A knurled dispensing attach with an inner plunger behaves as a syringe for that recoat material. To fill up the syringe, point the lever downward (i.e., towards the recoat container), then rotate the knurled dispensing screw counterclockwise till it spins easily to fill up the syringe (demonstrated inside the picture towards the right). Then, to inject the recoat materials to the mold, point the lever horizontally (i.e., facing the knurled screw) and rotate the screw clockwise until close to the end of the journey range is achieved. Steer clear of bottoming out iuwekk dispenser because this may damage the interior plunger; also be careful when re-engaging the threads to prevent go across threading the dispensing screw. A number of fill up/inject actions may be required until air is displaced inside the system. Use lens tissue plus an acetone or alcoholic beverages cleaning solution to collect any excess recoat material that flows through the mold.

Optical Fiber Proof-Testing Machine – Fresh Info On This Issue..

We are using cookies on our website

Please confirm, if you accept our tracking cookies. You can also decline the tracking, so you can continue to visit our website without any data sent to third party services.